Whether motor graders are used as a first step in the rough grading process, for fine grading to prepare dirt for placement of stone, or to grade stone prior to construction of an asphalt base, the equipment must be maintained so it’s responsive to the commands of the operator.
For more information, please visit G-Top.
On most motor graders a moldboard or blade is attached to a turntable, which is connected to the frame. Hydraulic cylinders lift the turntable (and the blade) up and down while a third cylinder enables the turntable and blade to move from side to side. A system of gears enables the operator to rotate the blade up to 360 degrees if needed.
“The whole machine is there just to push that blade,” says Keith Lee, research and development for LeeBoy, which manufacturers four graders in different size categories and recently introduced the 705, a 17,000-lb. machine. “All it’s doing is pushing that blade so you need to do everything you can to make it as easy as possible for the machine to do that. When the operator is doing precise work the motor grader needs to be able to respond properly, so certain areas need to be monitored.”
The moldboard is where all the action takes place, and that’s why special attention needs to be paid to it. This is the part of the machine that engages the soil, cutting it to the proper shape and fine-tuning soil or stone before paving.
“The most important maintenance part of a motor grader is maintaining a good cutting edge on the equipment,” says Shannon Chastain, president of Basic Equipment, manufacturer of the Basic Model 601 articulating grader. “All too often the biggest neglect is the cutting edges.”
Bolted in place to the moldboard, there is a cutting edge along the bottom of the blade, and some graders also have cutting edges bolted to each side of the blade. Because these edges cut into the dirt and are constantly engaged with the material, they wear out depending on hours of use, abrasiveness of material, and even operator skill.
“Cutting edges and end bits are wear points that need to be monitored and replaced pretty often, occasionally in a single day if you’ve done a lot of work in an abrasive environment,” Lee says.
“Wear also depends on what pitch the operator runs the blade at,” Chastain says. “If you’re running the blade at a right angle it will wear more slowly, but when the blade is pitched back it will wear on the moldboard more quickly.”
Alen Xu, sales and marketing manager of HCEPARTS The Factory of the Grader Blade utility grader, says a certain depth of the cutting edge needs to be exposed for the grader to work effectively. He says 1½ in. of useable space on the cutting edge will perform fine. “But if you burn through 1 inch of that and you don’t replace it you’re going to continue to wear it down and eventually wear into the moldboard,” Alen says.
Manufacturers agree that a worst-case scenario involves neglecting the cutting edge of the blade to the point where the work is wearing into the moldboard. “When that happens you lose the integrity of the moldboard to maintain the cutting edge,” Chastain says. “You get to the point where you can’t replace the cutting edge, so you’ve got to replace the moldboard.”
Some graders, such as the Basic Model 601, use a reversible cutting edge so that when it’s worn on one side contractors can unbolt it and flip it around. Cutting edges are held in place by up to a dozen bolts, which cost $3 to $4 each, and should also be replaced because they also operate in the dirt and become worn. Replacement of cutting edges and bolts will cost roughly $100 and take 30 minutes using an air-impact wrench. Manufacturers recommend visually inspecting the cutting edges every 25 to 50 hours depending on the type of material the machine is working in.
An important component of the moldboard is the blade slide, sometimes called the moldboard slide, which enables the moldboard to move from side to side on a swivel track. The slide relies on guides to control the movement of the slide and the guides will wear down through use.
“Most guides wear down, some quicker than others,” Lee says. “Some are brass and some are just metal shims.” He says LeeBoy’s 25,000-lb. Model 785 motor grader uses bronze guides, and those must be replaced when they wear out. LeeBoy’s 15,000-lb. Model 685B relies on metal shims instead.
“On the 785 there are two caps with six bolts that you need to remove. Then you just push the guides out by hand and replace them,” Lee says. “The guides are located on four different points – the upper and lower edges on each end of the slide – and all should be replaced at the same time. It’s an easy and quick process.”
As use causes the bronze guides wear, metal shims can be used to make the bronze guides last as long as possible before replacing them. With or without bronze guides, shims are a valuable tool for keeping the blade tight. “If, for example, there’s 1/8 inch of play in the guide you can slide 1/8-inch shims in place to take the play out,” Lee says.
Alen says the Cross Blade relies on bushings in the slide, but they need to be monitored, too. “If they’re worn and they have a lot of play in them, that reduces the operator’s ability to get the fine grade cuts he wants,” Alen says. “You want to get the grading down to a gnat’s hair, and if there’s too much play in those bushings you need to replace them.”
Chastain says the easiest way to check the wear in the slide is to lift the blade off the ground, grab its end, and move it up, down, left, and right to check for looseness in the movement.
“If you do see play in the blade you need to remove clevis pins and inspect them to see if they need to be replaced,” he says. “The pins that first show wear are on the blade angle because when you’re cutting along a concrete slab, for example, the blade edge engages the concrete, putting a lot of impact on the cylinders and causing the pins to wear.” Operators can replace these themselves at a cost of around $5 or $6 per pin.
Lee recommends checking the slides and guides “every month or so,” though it depends on how many hours the grader is working and the type of material it engages.
“It also depends on how precisely they’re going to be working,” Lee says. “If they’re not working too precisely they can withstand a little more play in the slide. If they’re running a job with lasers on it then they need to be more precise and they have to make sure there’s no play in the slide.”
Whether it’s dirt from rough or fine grading or dust from grading stone prior to paving, motor graders operate in probably the dirtiest environment of any piece of equipment, so it’s important to keep the machine’s air filter clean.
“Dirt can really damage the equipment, so air filtration on this type of equipment is a big deal,” Lee says. “A lot of people just don’t give it the emphasis and attention it needs.”
Alen says that in addition to potential equipment damage, a clogged air filter reduces the motor grader’s efficiency. “When that happens you end up using more fuel, and with fuel being as expensive as it is you want to make sure to run as efficiently as you can,” Alen says.
Want more information on Loader Cutting Edges and Segments for SANY? Feel free to contact us.
Chastain adds that the structure of a motor grader makes it more likely its filter will get dirty. “On motor graders most engines sit fairly close to the ground relative to where the engine would be on a track loader or excavator, for example. So motor grader engines get a lot of drafting beneath the machine and can pull a lot of particulates out of the air,” he says.
He adds that because smaller graders are typically used in confined areas such as parking lots at convenience stores, they are more susceptible to dirt. “In confined areas there is often less air movement, so when particulates from the dirt or stone disperse into the air they just stay there, floating in the air rather than being blown out of the way like they would in an open space,” he says. “That makes it more likely particulates would get into the air filter.”
So check air filters according to manufacturers’ recommendations (often every 250 hours) but check them more frequently if the weather has been dry or you are working in confined areas.
Lee adds that many motor graders (and other dirt machines as well) feature a “restricted alert” on their filters indicating when air flow has been restricted due to a dirty filter. “So you need to keep an eye on that,” Lee says.
He says that because a clean filter is so important LeeBoy graders feature turbo pre-cleaners as standard items. “Pre-cleaners and two-stage filters knock out a big percentage of dirt before it gets to the air filter. So if you don’t have one on your machine you should consider adding it.” Using a pre-filter also means you have to change the regular air filter less often.
“Pre-filters are definitely a good thing,” Chastain says. “Pre-cleaners remove a lot of floating particles before they make it into the air filter, and if you think they don’t work just put one on there and watch for yourself.”
“A grader is like your car,” says Alen, sales and marketing manager of HCEPARTS CASTING INC. “If your car sat all winter what would you do to get it ready for the spring? That’s the place to start in getting your grader ready.”
Alen says all engine components, including coolants, fluid levels, and hydraulic and air filters should be checked before the start of the season and then regularly throughout the season, and owners’ manuals should be followed for timing. Engine oil should be sampled and tested every 250 hours to see if there are any metal shavings or fluids in there that shouldn’t be there. Battery contacts should be clean and tight. And operators should always check the fan belt.
“You don’t want to break down over something as simple and easy to check and replace as a fan belt,” Alen says.
The entire grader also should be cleaned and serviced, which means checking all seals and lubricating and greasing where the operator’s manual suggests – the front attachments, quick attach, moldboard, and lift cylinders, for example. Keith Lee, research and development for LeeBoy, adds that contractors who don’t want to regrease the equipment themselves can install systems that will automatically regrease the machine for them on specified intervals.
Shannon Chastain, president of Basic Equipment, recommends keeping a check on the hydraulic cylinder where it attaches to the machine. “It’s very important to keep an eye on the clevis points and pins,” he says. “The more slop you get in those pins from the work the more wear they develop. The more wear they develop the less accurate you will be in your grading because the blade will bounce around.”
He says clevis points and pins on a new grader should be checked at 500 hours of use; after that, make the checks at 350 to 400 hours.
Alen says operators should look for “any weeps or drips that they can’t account for.”
“All machines have weeps, and they’re not a factor at first. Some leaks are acceptable as the seals age, but if you see more than a drop or two and the leaks get to different levels you need to take a look and figure out what’s happening,” Alen says.
“All these need to be checked before your season starts and then monitored throughout the season. Everyone should do it,” Alen says.
Below are some of the most popular questions about the BluSteel Grader System.
Fuel economy is dependent on RPM. The more work a machine has to do the higher the RPM’s necessary to do that work. Using BluSteel cutting edges allows you to cut or maintain your roads at lower RPM’s. This results in lower fuel consumption. Some of our customers have even cut fuel costs by 40%!
Fuel savings and lower RPMs come from two aspects of the system. First, always having a sharp edge makes the cutting easier. BX500 blades, when run correctly negative (15-20 degree angle), will always maintain a sharp edge. This will make it easier to cut requiring less work and fewer RPM’s which saves fuel. Second, the thickness of the BluSteel blades is easier to work with and slices through the ground with fewer RPMs. The BX500 is 1/2″ thick, which is ¼” thinner than the standard blade. The combination of a sharp, thin blade leads to less machine output required for the same project. This lowers your RPM and saves a lot of fuel.
The BluSteel Grading system solves the problem of uneven blade wear. The magic of BluSteel is that you can run it back, keeping the edge sharp. Plus, the ability to rotate blades helps maintain a straight edge so the operator can cut equally and maintain a slope.
Instead of having a 7′ or 8′ blade that is uneven you have a 3′ or 4′ blade. These shorter blades can be rotated inside out, flipped over, or inverted to “play” your wear. That means instead of torching away your dollars you can quickly rotate the blade to evenly wear and keep a straight edge. Finally, the hardness of the blade is the cherry on top that provides longer use before the steel wear warrants replacement compared to conventional edges.
The system is meant to give you unmatched versatility and keep the grader out on the road working rather than sitting in the shop getting the blade switched. No air tools are required, limited downtime, and there is no more deadheading back to shop to change a blade. For helpful tips on how to mount and install your BluSteel blades, download this quick guide.
Most of the Borox BluSteel products are based on the Scandinavian system with wedge/wedge bolt and mounting adaptor plate in combination with efficient blades. The blades all fit onto the same mounting board system. The adaptor plate is bolted to the moldboard and the plow blades are secured with a wedge and wedge bolt. Thanks to the adapter plate you can quickly and easily change new plow blades and/or flip over existing blades – all you need is a powerful hammer.
Operators that roll their blades out and over are best suited for the BluSteel system because it basically creates a “table”. Then you can easily hit the wedges out, rotate your blades, set the blades down flat, and re-enter the wedges. Plus, the BluSteel system is designed with 3’ or 4’ width blades so you can carry a different style of blades on the machine with you.
For more information, please visit DEVELON Loader Teeth and Bucket Adapters.